search

Lippert-components Coach Step Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Lippert-components Coach Step. Lippert Components Coach Step User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 4
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
LIPPERTCOMPONENTS, INC.
COACH STEP
INSTALLATION, OPERATION AND SERVICE MANUAL
AUTOMATIC ELECTRIC STEPS AND AUTOMATIC ELECTRIC SLIDING STEPS
FOR
RECREATIONAL VEHICLES
INSTALLATION PREP
WARNING!
Keep clear of steps as they are deployed. Step actuation takes approximately two seconds whether extending or retracting.
Keep hands and fingers away from step mechanism during actuation process to prevent serious bodily injury.
TEST PROCEDURE PRIOR TO INSTALLATION
1. Steps will install easier when extended first. Place steps upside down on workbench or floor.
2. Cut and connect four (4) jumper wires to the 4-pin connector. Match the jumper wires to the posts on the connector color for color.
3. Connect GREEN WIRE to the NEGATIVE post of a fully charged, 12V automotive battery.
4. Connect RED and WHITE WIRES to the POSITIVE post of the battery.
5. Connect the BROWN WIRE to the NEGATIVE post of the battery.
WARNING!
Steps will extend immediately!
6. Disconnect jumper wires from the battery.
INSTALLATION
Steps must be installed using four (4) 5/16”, GR 8 bolts, lock washer and nuts for the Automatic Elctric Steps and 3/8” bolts, lock washers and
nuts for the Automatic Electric Slideing Step. Retract steps by attaching wires in the following sequence:
1. Ground the GREEN WIRE to the chassis.
2. Touch the RED and WHITE wires to the positive terminal on the battery.
WARNING!
Keep clear of the steps as they will retract quickly.
Proceed to install door switch and power switch(items not included). The wires of the four pin connector must be routed as follows:
1. WHITE - Connect to power switch (16 ga. min. wire).
2. YELLOW - Must be connected to power source that is only hot when ignition is “ON.” Protect with 6A fuse or breaker (16 ga. min. wire).
3. RED - Connec to power for motor. Protect with 25A fuse (10 ga. min. wire).
4. BROWN - Connect to door switch (16 ga. min. wire).
3
2
1
4
Fig. 1
Vista de pagina 0
1 2 3 4

Indice de contenidos

Pagina 1 - LIPPERTCOMPONENTS, INC

LIPPERTCOMPONENTS, INC.COACH STEPINSTALLATION, OPERATION AND SERVICE MANUALAUTOMATIC ELECTRIC STEPS AND AUTOMATIC ELECTRIC SLIDING STEPSFOR RECREATION

Pagina 2 - +

+ -DOOR SWITCHBATTERYPOWERSWITCHTO FUSEPANEL6A FUSE6A FUSECIRCUITPROTECTORBROWNYELLOWWHITEREDGREEN-GROUND TOCHASSISOPERATIONWARNING!Look downwa

Pagina 3

WARNING!With Power Switch “ON,” door open and steps extended, it is possible to drive off. Damage to steps or vehicle is possible, as wellas serious

Pagina 4

SERVICE NOTESA. Use locktite on any bolts removed and replaced.NOTE: It is recommended that if the nut is removed and replaced in the field, a liqui

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Hardware Lippert-components Coach Step
Hardware Lippert-components Bike Rack & Tire Carrier Manual de usuario   (11 paginas)
Hardware Lippert-components Tent Camper Bike Rack Manual de usuario   (8 paginas)
Hardware Lippert-components Bike and Tire Rack Manual de usuario   (15 paginas)
Hardware Lippert-components Flow Down Aftermarket Manual de usuario   (4 paginas)
  • Zach and Dani's 2X Pittsburgh Corning CitEcar Davis Instruments
  • Netgear Antenas de la red Sony Computadoras móviles de mano Avaya Puntos de acceso wlan Parkside Los Sistemas De Alimentación De Pulverización Fina, Epson Herramientas de medición y de diseño
  • Alpine iDA-305 Casio CT-X5000 AEG L6TBK62W Masimo Rad-5 Sennheiser EM 300
  • Bbk DL385DC Manual de usuario HP Switch KVM Manual de usuario HP ProOne 600 G1 All-in-One PC Manual de usuario Mitsubishi Electric FR-D700 Manual de usuario Axis P8513 Manual de usuario